Tongue Depressor - Revision history

Admin: 9 revisions

2010-08-20T18:03:57Z

9 revisions

2008-05-28T00:36:43Z

2008-05-28T00:29:50Z

2008-05-28T00:29:36Z

2008-05-28T00:29:04Z

2008-05-28T00:07:46Z

2008-05-28T00:06:58Z

2008-05-28T00:06:14Z

2008-05-28T00:05:11Z

2008-05-28T00:00:09Z

New page: Tongue Depressor/Mixing Sticks

New page

Tongue Depressor/Mixing Sticks

@@ Line 4: / Line 4: @@
 == Velocity Use ==
-What can't these things be used for?  Use them for mixing epoxy and applying [[Microballoons|micro]].  Glue them in place to hold the sides of your NACA ducts out.  Cut them into triangles to hold up your fuel baffles, or to put gentle pressure on your windows while they cure.  As they say, "but wait... there's more..."<br/>
+What can't these things be used for?  Use them for mixing epoxy and applying [[Microballoons|micro]].  Glue them in place to hold the sides of your [[NACA Ducts]] out.  Cut them into triangles to hold up your fuel baffles, or to put gentle pressure on your windows while they cure.  As they say, "but wait... there's more..."<br/>
 == Packaging Weights ==

@@ Line 4: / Line 4: @@
 == Velocity Use ==
-What can't these things be used for?  Use them for mixing epoxy and applying micro.  Glue them in place to hold the sides of your NACA ducts out.  Cut them into triangles to hold up your fuel baffles, or to put gentle pressure on your windows while they cure.  As they say, "but wait... there's more..."<br/>
+What can't these things be used for?  Use them for mixing epoxy and applying [[Microballoons|micro]].  Glue them in place to hold the sides of your NACA ducts out.  Cut them into triangles to hold up your fuel baffles, or to put gentle pressure on your windows while they cure.  As they say, "but wait... there's more..."<br/>
 == Packaging Weights ==

@@ Line 11: / Line 11: @@
 == Directions for Use ==
 [[Image:tongue_square.jpg|right|thumb|Mixing Sticks cut square]]
-I tend to cut the end off square for mixing epoxy, as well as applying micro/schmooey.  I use the round end for making a nice radius.
+I tend to cut the end off square for mixing epoxy, as well as applying [[Microballoons|micro/schmooey]].  I use the round end for making a nice radius.
 == Safety and Handling ==
 It's a damn stick.  Keep it out of your eye.<br/>

@@ Line 1: / Line 1: @@
 [[Image:Tonguedepressors.jpg|right|thumb|Mixing Sticks]]
 == General Description ==
-A structural resin filler. The mixture of cotton fiber and epoxy is referred to as "flox". The mixture is used in structural joints and in areas where a very hard, durable buildup is required. Flox is mixed in much the same way as dry micro but only about two parts flock to one part epoxy is required. Mix in just enough flock to make the mixture stand up. If "wet flox" is called out, mix it so it will sag or run. Flox is often used to reinforce a sharp corner. Paint a light coat of pure epoxy inside the corner, trowel flox in to make a triangular support. The flox corner is done just before one glass surface is applied for a wet bond to one surface.<br/>
+It's a piece of wood 3/4" by 6" long, maybe 1/8" thick.<br/>
 == Velocity Use ==

← Older revision		Revision as of 00:07, 28 May 2008
Line 1:		Line 1:
−	~~Tongue Depressor/Mixing Sticks~~
	[[Image:Tonguedepressors.jpg\|right\|thumb\|Mixing Sticks]]		[[Image:Tonguedepressors.jpg\|right\|thumb\|Mixing Sticks]]
	== General Description ==		== General Description ==

← Older revision	Revision as of 18:03, 20 August 2010
(No difference)

← Older revision		Revision as of 00:05, 28 May 2008
Line 1:		Line 1:
	Tongue Depressor/Mixing Sticks		Tongue Depressor/Mixing Sticks
		+	[[Image:Tonguedepressors.jpg\|right\|thumb\|Mixing Sticks]]
		+	== General Description ==
		+	A structural resin filler. The mixture of cotton fiber and epoxy is referred to as "flox". The mixture is used in structural joints and in areas where a very hard, durable buildup is required. Flox is mixed in much the same way as dry micro but only about two parts flock to one part epoxy is required. Mix in just enough flock to make the mixture stand up. If "wet flox" is called out, mix it so it will sag or run. Flox is often used to reinforce a sharp corner. Paint a light coat of pure epoxy inside the corner, trowel flox in to make a triangular support. The flox corner is done just before one glass surface is applied for a wet bond to one surface.<br/>
		+
		+	== Velocity Use ==
		+	What can't these things be used for? Use them for mixing epoxy and applying micro. Glue them in place to hold the sides of your NACA ducts out. Cut them into triangles to hold up your fuel baffles, or to put gentle pressure on your windows while they cure. As they say, "but wait... there's more..."<br/>
		+
		+	== Packaging Weights ==
		+	The factory sells these in boxes of 500.
		+
		+	== Directions for Use ==
		+	I tend to cut the end off square for mixing epoxy, as well as applying micro/schmooey. I use the round end for making a nice radius.
		+
		+	== Safety and Handling ==
		+	It's a damn stick. Keep it out of your eye.<br/>