Difference between revisions of "Material Sources"
| Line 19: | Line 19: | ||
<b>NOTE:</b> I support buying as much from the factory as you can. I find that their prices are reasonable, and hey, they need to make a buck to be around for us in the future. However, if you must, here are other sources.<br/> | <b>NOTE:</b> I support buying as much from the factory as you can. I find that their prices are reasonable, and hey, they need to make a buck to be around for us in the future. However, if you must, here are other sources.<br/> | ||
~Brett | ~Brett | ||
| + | === Brake Parts === | ||
| + | 3/16" Nylaflow (H thick wall) is the standard factory tubing ([http://www.aircraftspruce.com/catalog/appages/nylaflow.php Spruce]) ([http://www.wicksaircraft.com/catalog/product_cat.php/subid=2158/index.html Wicks])<br/> | ||
| + | Richard Gentil recommends using Versatube ([http://www.aircraftspruce.com/catalog/mepages/3003versatube.php Spruce]) ([http://www.wicksaircraft.com/catalog/product_cat.php/subid=1833/index.html Wicks])<br/> | ||
| + | |||
=== Control Parts === | === Control Parts === | ||
Rudder Pulley - MS24566-1B ([http://www.aircraftspruce.com/catalog/appages/phenolicpulleys.php Spruce]) ([http://www.wicksaircraft.com/catalog/product_detail.php?pid=5990 Wicks])<br/> | Rudder Pulley - MS24566-1B ([http://www.aircraftspruce.com/catalog/appages/phenolicpulleys.php Spruce]) ([http://www.wicksaircraft.com/catalog/product_detail.php?pid=5990 Wicks])<br/> | ||
Revision as of 12:24, 19 June 2008
Contents
Electrical
RG-142 Supplier
RG-142 coax Mil-Spec is the same diameter as RG59 and about the same loss as RG6. This lets you place your transponder antenna in the strake end with little loss. See the following address
https://2298362093.monstercommercesites.com/index.asp?PageAction=VIEWPROD&ProdID=1659
Skycraft Parts & Surplus is a great place to find many electrical parts for your aircraft. Located in Orlando, FL
Jim Agnew
Fiberglass/Composite
Hardware
| The Yard |
McMaster Carr |
Velocity Specific
NOTE: I support buying as much from the factory as you can. I find that their prices are reasonable, and hey, they need to make a buck to be around for us in the future. However, if you must, here are other sources.
~Brett
Brake Parts
3/16" Nylaflow (H thick wall) is the standard factory tubing (Spruce) (Wicks)
Richard Gentil recommends using Versatube (Spruce) (Wicks)
Control Parts
Rudder Pulley - MS24566-1B (Spruce) (Wicks)
Control System Bushings - AN111-6 (for AN3 3/16" diameter bolts) (Spruce) (Wicks)
VRSC-01 - Rudder Wire - 1/6" stainless was standard until June 2008 (Spruce) (Wicks)
VRSC-01 - Rudder Wire - 3/32" stainless standard after June 2008 (Spruce) (Wicks)
Rudder Wire Nicopress sleeves - 18-1-C (Spurce) (Wicks)
MM-4/MW-4 Control Rod Ends (Spruce) (Wicks)
VAUJ-01 - 3" long piece of 5/8" x .058 wall steel tube (Spruce) (Wicks)
