Documents
IO540 Type Certificate
O540 Type Certificate
Airventure Article by Jack Watson
Air/Oil Separator Article by Don White
Koch Chart
Crosswind Chart
Weight and Balance
Dale Alexander and Ronnie Brown
NACA Ducts
Media:nacascoop1.xls
Andy Millin
Media:NACA Article SA 12-01.pdf
AC 43.13 Acceptable Methods
{ |- |Cover |Purpose |Table of Contents |CH1.1: Wood Structure |Ch1.2: Health and Safety |- |CH.3: Inspection |CH1.4A: Repairs |CH1.4B: Repairs Continued |CH1.5: Finishing | |- |CH2.1: Fabric Covering |Ch2.2: Dope |Ch2.3: Inspection |CH2.4: Repairs | | |- |Ch3.1: Composites |Ch3.2: Metal Sandwich Repair |CH3.3: Transparent Plastics |Ch3.4: Windshields | |- |CH4.1: Metal Structure |CH4.2: Testing |CH4.3: Precautions |Ch4.4: Repair |CH4.5: Welding |- |CH5.1: ND Testing |CH5.2: Visual Inspection |CH5.3: Eddy Current |CH5.4: Magnetic Particle |CH5.5: Penetrant Inspection |- |CH5.6: X-Ray Inspection |CH5.7:Untrasonic Inspection |CH5.8: Tap Testing |CH6.1: Corrosion Inspection |CH6.2: Types of Corrosion |- |CH6.3:Corrosion Protection |CH6.4: Corrosion Maintenance |[[Media:2j-ch6_5.pdf|CH6.5: Visual Inspection] |CH6.6: Corrosion Removal |CH6.7: Corrosion Removal |- |CH6.8: Aluminum |CH6.9: Magnesium |CH6.10: Ferrous Metals |CH6.11: Other Metals |CH6.12: Plated Parts |- |CH6.13: Corrosion Proofing |CH6.14: Water Immersion | | | |- |CH7.1: Aircraft Hardware |CH7.2: Screws |CH7.3: Bolts |CH7.4: Nuts |CH7.5: Washers |- |CH7.6: Pins |CH7.7: Safteying |CH7.8: Control Cables |CH7.9: Turnbuckles |CH7.10: Turnbuckle Safety |- |CH7.11: Hardware Identification | | | | |- |CH8.1: Engines, prop, fuel |CH8.2: Fuel |CH8.3: Exhaust |CH8.4: Repairing Metal Props |CH8.5: Inspecting Propellers |- |CH8.6: Propeller Tracking | | | | |- |CH9.1: Aircraft Systems |CH9.2: Hydraulic Systems |CH9.3: Emergency Equipment |[[Media:3n-ch9_4.pdf|CH9.4: Cabin Interior] | |- |CH10.1: Weight and Balance |CH10.2: Weighing Procedures | | | |- |CH11.1: Electrical Systems |CH11.2: Storage Batteries |CH11.4: Circuit Protection |CH11.5: Wire Rating |CH11.6: Wire Selection |- |CH11.7: Acceptable Wire |CH11.8: Wire Installation |CH11.9: Electrical Inspection |CH11.10: Service Loop |CH11.11: Clamping |- |CH11.12: Wire Insulation |CH11.13: Splicing |CH11.14: Terminal Repairs |CH11.15: Bonding |CH11.16: Wire Marking |- |CH11.17: Connectors |CH11.18: Conduits |CH11.19: Unused Connectors |CH11.20: Electrical Symbols | |- |CH12.1: Avionics |CH12.2: Ground Checks |CH12.3: Ground Checks 2 |CH12.4: Test Equipment |Glossary }
